Texas Flange

RTJ Face Dimensions. 72 ... (a)- Bolt hole diameter 1/8 in. larger than bolt diameter. ...... ASME has incorporated most of the MSS-SP44 specification into B16.47 ...

FLANGE ISOLATING GASKET KITS

of ring-type-joint flanges. ... Standard thickness of 1/8”. ... provide the specifications of your flange using our convenient worksheet. ... No re-torquing required ...

Garlock Metallic Gasket Catalog

D-8. RW, RWI, SW (For ASME flanges) ................ D-8. MC, MCR (For boiler manholes) .................... D-9. HH (For boiler ... Torque Tables . ... Specifications subject to change without notice. This edition ..... API ring joint gaskets (RTJ). ■ Saves ...

GATE, GLOBE, CHECK, BUTTERFLY AND NEEDLE VALVES ...

This general specification covers the minimum technical requirements for the .... descriptions or in any situation where break-away torque requirements ... be in accordance with Appendix 8 of the ASME Boiler and Pressure Vessel Code, Section .... -29°C to 400°C ANSI Class 1500, Conforming to API 602, RTJ flanged ends ...

RECOMMENDED BOLT TORQUE REQUIREMENTS

For Ring Type Joint Gaskets ... Recommended Minimum Torque Values (Nm) ... 8. ⅝. 276. 79. 116. 178. 5''. 8. ¾. 276. 139. 203. 313. 6''. 8. ¾. 276. 139. 203. 313 ...

Ball Valves - Complete Solutions for Industrial Valves

Soft Seat Material. Torque and Cv Table. Page. 1. 2~3. 4~5. 6~7. 8~9. 14~17 .... C=BW Sch. 80. D=BW Sch. 160. E=BW Sch XXH. J=RTJ. R=Raised Face ... NEWAY reserves the right to change design, materials or specifications without notice ...

Valve Terminology Glossary

the multiplication of torque achieved. Back seat A shoulder on .... Ring type joint (RTJ) A flange connection using a specially shaped soft metal ring as a gasket.

Ring Type Joint Gaskets

Qualified engineers are always available for technical audits, advice on specifications or .... 17.5. 15.9. –. 1.075. 1.047. R31*. –. 3. 3. –. –. 3 1/8. –. 123.83. 11.11. 17.5. 15.9. 4.8. 1.130. 1.10. R32 ...... Excellent torque retention. • Good chemical ...

www.valves.co.uk DOUBLE BLOCK & BLEED VALVE SOLUTIONS

NACE - /NA Compliance to NACE specification MR-01-75 latest revision – suitable for sour service ... Rugged, 316 stainless steel, low torque, quarter turn ..... 3/8”. 10mm. 9/16”. 14mm. 13/16”. 20mm. SIZE. FLANGE. CLASS. RF/RTJ. FLANGE ...

KST Gaskets

T. (051)8. 6. 3. -. 17723 www.designjin.net. Korea Seal Tech. Gaskets ..... Use a torque wrench and well-lubricated fasteners with hardened flat ... Ring Type Joint .... these specifications are very similar, KST is making the change necessary for ...

NORSOK STANDARD L-004 Piping fabrication, installation, flushing ...

8. 5.5. Dimensional tolerances for pre-fabricated piping assemblies. 8. 5.6 ... as far as possible, intended to replace oil company specifications and serve as ..... Ring type joints (RTJ) rings are to be lightly smeared on the mating surface with a ... shall have controlled tightening by means of manual torque wrenches or ...

Model 3201 Liquid Level Controller

that meet NACE MR-01-75 specifications for sour service. zMallard ... Flanged 2", 3", 4", 6", or 8" ... 600# RTJ. /. 1480 psig (102 bar). 900# RF. /. 2220 psig (152 bar). 900# RTJ ... Torque Bar then rotates until the forces are again balanced.

TECHNICAL SPECIFICATION

lock up torque converter ..... 2M Flange with two (2) of 8” Series 600 RTJ ... CONTRACTOR to list giving full specifications, dimensions, and quantity (See also F5 ...

Shut-Off Pig Valves

8” 600 RF. 29.00. 12.00. 11.50. 19.12. 12.62. 9.00. 2550. 8” 600 RTJ. 29.12 ... torques and lower the sudden shock of pressure when the valve is cycled open to launch a .... All specifications and materials are subject to change without notice.

Network Scan Data

0 Mating mismatched ring-joint to raised-face flanges (VCFS will seal RTJ and ... 1) Flange Specification (currently offered only for ANSI B 16.5 flanges, contact Pikotek .... Diameter of Bolts Torgue Value. (inches) (Ft. lbs.) 1/2 30. 9/16 45. 5/8 60 ...

JOB SPECIFICATION FOR APPLICATION OF TORQUE AND ...

The purpose of this specification is to describe the methodology for ... hydraulic tensioner or by application of calculated bolt torque with calibrated torque wrenches. .... of 4 bolts each (i.e. 1-2-3-4, 5-6-7-8, 9-10-11-12 etc.) ...... RTJ SOFT IRON ...

Rosemount 1199 Seal Systems Manual

2-8. Differences between Electronic Remote Sensors and Capillary Systems . . . . . . . . 2- ...... The torque specifications for the saddle seal upper housings are. 360 in-lb ...... FCW Flush Flanged Seal – Ring Type Joint (RTJ) Gasket Surface. 2-in.

Guidelines for safe seal usage -Flanges and Gaskets -

8. Background to environmental legislation. The modern sealing challenge. 3. .... Tighten with torque wrench .... Similarly, testing specifications for traditional soft gasket materials were .... The gaskets involved are often referred to as RTJ or ...

Useful - Alliance Sealing

Specialized Ring Type Joint . ... III - Gasket Installation. 47. Bolt Torque Sequence . ..... of 1/32”, 1/16” and 1/8” in cut gaskets and 60” x 60” sheet. With its wide ...

Suppliers to the worlds Oil and Petrochemical Industries

NPT, Socket Weld, Butt Weld, Flanged RF/RTJ. Materials A105N, LF2, F316L - Trims 8, 5, 10, 12 and 16. Gate, Globe and Swing Check. 2” to 48” – Design API ...